Anodizing Tolerances for CNC Parts: How to Protect Bearing Fits and Threads

Anodizing-Tolerances-for-CNC-Parts-How-to-Protect-Bearing-Fits-and-Threads

Table of Contents

Anodizing tolerances matter whenever a CNC-machined aluminum part includes bearing bores, close-clearance shafts, threaded ports, sealing faces, or sliding features. Unlike paint, anodizing is not simply added on top of the surface. Part of the aluminum is converted into oxide, while part of the coating grows outward. If this dimensional change is not considered before machining, a finished bore can become too small, a shaft can become too large, or a thread can lose usable clearance.

For production parts, the drawing should define the required finish, coating thickness, dimensions that apply after anodizing, and any masking requirements. The machining supplier and anodizer should then confirm the allowance from their validated process—not from a generic online rule.

MXY Machining supports CNC machining services and surface finishing for aluminum parts. This guide explains how to plan anodizing tolerances before releasing a drawing for quotation.

Why Anodizing Changes Finished-Part Dimensions

Why-Anodizing-Changes-Finished-Part-Dimensions

Anodizing is an electrochemical process that converts part of an aluminum surface into aluminum oxide. The oxide layer provides corrosion resistance, appearance options, and in the case of Type III hard anodizing to improved wear resistance.

A practical planning rule often used for many anodizing processes is that approximately half of the finished coating thickness penetrates the original surface and approximately half builds outward. However, this is an estimate, not a universal engineering guarantee. Alloy, coating type, specified thickness, racking, geometry, pretreatment, sealing, and the anodizer’s controlled process can all affect the final result.

The U.S. military performance specification for anodic coatings, MIL-PRF-8625, covers several coating types and identifies broad thickness ranges. It also warns that force fits can damage anodic coatings because they are hard and brittle. MIL-PRF-8625 details

Feature (coating on both opposed surfaces)
Dimensional change
At 20 µm coating
At 50 µm coating
Outside diameter, or width across two faces
+1 × t
+20 µm
+50 µm
Bore diameter, or slot width
−1 × t
−20 µm
−50 µm
Single flat face or one-sided land
+0.5 × t
+10 µm
+25 µm
60° thread pitch diameter
≈ 2 × t
≈ 40 µm
≈ 100 µm
60° thread major and minor diameter
≈ 1 × t
≈ 20 µm
≈ 50 µm

Coating Thickness Tolerance by Anodizing Type

Coating
Typical production thickness
How thickness is controlled
Absolute variation to budget
Type II, clear or natural
5–10 µm
Coating weight (1000 mg/ft² minimum for Type II); thickness target from the drawing
Commonly 0 to +10 µm; confirm per supplier
Type II, dyed (Class 2)
10–20 µm
As above; dye uptake needs enough film to colour reliably
Roughly ±5 µm in good practice
Type III hardcoat, default
50 µm (0.002 in)
±20% of nominal up to 0.002 in
40.6–61.0 µm, a 20 µm band
Type III hardcoat, heavy
50–114 µm
±0.0004 in (±10 µm) above 0.002 in
20 µm band
Thin or conductive anodize
3–5 µm
Drawing or purchase order
Small, but not zero

The Type III line is the one that breaks fits. MIL-PRF-8625F §3.7.2.1 sets a default nominal of 0.002 in and permits the coating to vary by ±20% at that thickness. Twenty percent of 50 µm is 10 µm, and because a bore has two coated walls, that permitted variation alone moves the diameter by 20 µm. On a Ø40 mm H7 bore the entire tolerance band is 25 µm. The coating tolerance consumes 80% of it before a single chip is cut.

Note the asymmetry in how the standards work: Type III has an explicit numeric thickness tolerance written into the specification, while Type II is controlled primarily by coating weight and by whatever thickness the drawing names. That is why a “standard” anodize callout on a tight bore is not a neutral default, it can be looser than the fit it is meant to protect. It is also the practical heart of anodizing tolerances: the thicker the film, the larger the absolute number you have to defend.

Worked Example: A Ø40 H7 Bearing Bore

anodizing-bore-tolerance-stack
The design. A 6061-T6 aluminum housing carries a Ø40 H7 locating bore, 40.000–40.025 mm, a band of 25 µm. It takes a ground steel shaft at Ø40 g6, 39.975–39.991 mm. Design clearance therefore runs from 9 µm at the tight end to 50 µm at the loose end. The housing is finished Type II black anodize, 20 µm nominal, specified as 15–25 µm. The bore is not masked.
 
Step 1 — dimensional consequence. The bore has two coated walls, so it closes by one coating thickness. At 15 µm the bore loses 15 µm; at 25 µm it loses 25 µm.
 
Step 2 — required pre-anodize window. Work backwards from the finished limits, using the worst coating case at each end:
  • At the small end, the bore must not finish under 40.000 after the thickest coating: pre-anodize minimum = 40.000 + 25 = 40.025.
  • At the large end, it must not finish over 40.025 after the thinnest coating: pre-anodize maximum = 40.025 + 15 = 40.040.
The pre-anodize target is 40.025–40.040, a 15 µm window, centred on 40.0325.
 
Step 3 — check all four corners. A tolerance stack is only verified when every combination of extremes has been tested, not just the nominal.
 
Case
Pre-anodize bore
Coating
Finished bore
Verdict
Small stock, thick coating
40.025
25 µm
40.000
At limit, passes
Small stock, thin coating
40.025
15 µm
40.010
Inside band
Large stock, thick coating
40.040
25 µm
40.015
Inside band
Large stock, thin coating
40.040
15 µm
40.025
At limit, passes
Finished bore: 40.000–40.025. Clearance against the g6 shaft runs 9 µm to 50 µm, exactly as designed. The stack closes.
 
Step 4 — see what the obvious approach does. Suppose the drawing says Ø40 H7 and the shop does the reasonable thing: machine to 40.000–40.025 and send it to anodize.
 
Case
Pre-anodize bore
Coating
Finished bore
Result
Small stock, thick coating
40.000
25 µm
39.975
25 µm undersize; 16 µm interference with shaft
Large stock, thin coating
40.025
15 µm
40.010
Passes
The worst case is not a near miss. The bore finishes 25 µm below its lower limit and interferes with the shaft by 16 µm at the same time. That is a press fit that was specified as a clearance fit, arriving as a scrap part with a perfect inspection record.
 
Step 5 — note what this costs you. The available machining window collapsed from 25 µm to 15 µm. On a 30–50 mm diameter, 25 µm is IT7 and 15 µm is IT6. The coating did not merely shift the bore; it moved the part up a tolerance grade. That is the real price of compensating instead of masking, and it is why the decision in the next section matters more than the arithmetic.
 
If you are setting tolerances on a part for the first time, the general bands in our machining tolerances chart are the right starting point before anodize enters the picture, and CNC machining tolerances explained covers how those bands interact with process capability.
 

Type II vs. Type III: Tolerance Planning Differences

Type II anodizing is often used for corrosion resistance and appearance. Type III hard anodizing is generally selected for wear resistance and can use a thicker coating. Both require dimensional planning, but the risk to close fits rises as coating thickness increases.

ConsiderationType II AnodizeType III Hard Anodize
Typical useCorrosion protection, appearance, dyed finishesWear resistance, engineering surfaces
Dimensional impactUsually lower, but still relevant for precision featuresOften higher; must be planned for bores, shafts, and threads
Close fitsConfirm finished dimensionsMask or validate allowance for critical fits
Force-fit assemblyReview before releaseTreat cautiously; coating can be damaged
InspectionConfirm where requiredInclude coating thickness and post-finish fit checks

A Drawing Callout You Can Copy

  1. FINISH: ANODIZE PER MIL-PRF-8625, TYPE II, CLASS 2, BLACK
  2. COATING THICKNESS: 20 µm ± 5 µm, measured per ASTM B244, min. 8 readings
  3. DIMENSIONS ARE FINISHED-PART (AFTER COATING) UNLESS MARKED “PRE-FINISH”
  4. PRE-FINISH TARGET: Ø40 H7 BORE TO BE MACHINED 40.025–40.040
  5. MASK: Ø40 H7 BORE (FULL DEPTH), M8×1.25 THREADS (FULL THREAD), DATUM A FACE
  6. MASKED SURFACES TO REMAIN BARE; APPLY CONVERSION COATING PER MIL-DTL-81706 CLASS 1A
  7. COATING-FREE BOUNDARY: 1.0 mm MAX STEP, NO FILM INSIDE MASKED ZONE
  8. CONTACT MARKS: NON-FUNCTIONAL SURFACES ONLY, MAX 2 PER PART
 
Four of those lines are doing heavy lifting, and they are the four usually missing:
  • The thickness is a range in micrometres, not a finish name. “Type II anodize” does not tell anyone what the film will measure.
  • Dimensions are declared as after coating, so inspection has one target rather than two.
  • The pre-finish target is derived and written down, so the machinist is not asked to invent it.
  • Masking is enumerated by feature, with a boundary tolerance, so the anodizer is not guessing which bore you meant.
 
If your RFQ package needs a structure for this, the CNC machining RFQ checklist covers the drawing, finish and inspection information that prevents exactly these back-and-forth loops.

Request a CNC Machining and Anodizing Review

Plan anodizing before machining starts. Do not treat it as only a final cosmetic finish. Send MXY Machining your 3D model, 2D drawing, aluminum alloy, required coating specification, coating thickness, quantity, and a list of critical fits. Our team can review the part for manufacturability, masking requirements, pre-finish allowances, and finished-part inspection needs.

For a practical example of machining, tapping, black anodizing, and inspection in one workflow, see this 6061 aluminum prototype housing case study.

Frequently Asked Questions

Does anodizing change the dimensions of an aluminum part?
Yes, and by enough to matter on tight features. The anodizing dimensional change is not a rounding error: the coating grows roughly half its thickness outward from the original surface and half into the substrate. A 20 µm coating raises a flat face by about 10 µm, adds about 20 µm to an outside diameter, and removes about 20 µm from a bore.
The anodizing dimensional change across a bore is about one coating thickness, because both walls grow inward. A 20 µm coating closes a bore by roughly 20 µm; a 50 µm Type III coating closes it by roughly 50 µm. A Ø40 H7 band is 25 µm, so the hardcoat case exceeds the entire tolerance.
Yes, but the thread must be designed for it. A 60° thread’s pitch diameter moves about four times the growth per surface — roughly twice the coating thickness — which on an M8 × 1.25 6H thread means 40 µm at 20 µm coating, or 63% of the class allowance at 50 µm. Mask the thread, tap oversize against a validated allowance, or specify a thinner coating.
Compensate when the coating range is less than about half the finished tolerance band and the machining process can still hold the reduced window; mask when the band is 20 µm or tighter, when the coating range approaches the band, or when the feature’s function is sensitive to a few micrometres. Masking trades machining risk for labour cost, which is usually the better trade on bearing seats and threads.
A range in micrometres, chosen against the fit rather than copied from a finish name. MIL-PRF-8625F permits ±20% on Type III up to 0.002 in and ±0.0004 in above it, which is a 20 µm band either way — wide relative to an H7 bore. Where a fit depends on it, specify the range explicitly and let the supplier confirm the capability.
The mechanism is identical; the magnitude is not. Type III runs at roughly 50 µm nominal with a permitted ±20%, so the absolute variation is an order of magnitude larger than decorative Type II at 10–15 µm. The same bore that survives Type II unmasked will usually need masking under Type III.

Share This Post

Ready to Elevate Your Project?

Bring Your Designs to Life with MXY Machining

Experience precision engineering with MXY Machining. From detailed prototypes to high-volume production, we’re here to turn your concepts into reality. Contact us today to discuss your project needs!

Related Articles and Insights

Enhance your knowledge and stay informed with our comprehensive collection of articles and posts. Each piece is carefully curated to align with your specific interests, offering insights and updates that resonate with your industry needs.

Fill This Detailed Form